Kc-hilites KC #326 (240w) LED Light Bar System Instructions Manuel d'utilisateur télécharger pdf

Bolts with Nuts

on Brackets

Thanks for choosing a KC HiLiTES product. We take pride in building the highest quality, best

engineered systems possible. Your satisfaction with our product is important, so if you have any

questions, please call our customer service line at 800-528-0950.

WIRING YOUR LIGHT

1. Remove the fuse from the harness. Find a suitable location inside the

passenger compartment for your switch. Mark and drill two 1/8” holes, insert screws and loosely install

the panel to ensure fit. Remove panel, install switch, and slide panel with switch, back in place. (Do

not tighten. The panel and switch will be removed when attaching wires.)

2. Connect the wire to the light and route the harness back toward the 12V battery or power source.

Attach the relay within 24” of your power source. (DO NOT CONNECT TO BATTERY AT THIS TIME)

3. Continue routing the white and green wires of the harness into the vehicle toward the switch. Once the

wires are inside the vehicle near the switch, remove the panel with switch and attach the green wire to

the switch terminal marked LOAD. Attach the white wire to the switch terminal marked LOAD. Attach

one end of the brown wire to the switch terminal marked EARTH and the other end to a good

grounded metal surface under the dash. Re-attach the panel with switch

and secure with screws.

4. Before attaching wires to the power source, ensure the switch is in the

OFF position (see photo) At your 12V power source, connect the yellow

wire to positive 12V and the black wire to a good chassis ground or

negative post on the battery.

5. The white wire is the trigger for the relay and must be connected to a

12V power source. We recommend a source that is activated by the

ignition switch so the lights will shut down when the key is off.

6. Replace the fuse and turn on your lights.

7. You’re done.

Parts Included

1 - LED Light Bar

3 - Brackets

6 - SS Bolts & Nuts

1 - Wiring Harness Kit

MOUNTING YOUR LIGHT

1. Add three SS bolts to the bar by inserting the bolt heads in the hole at

the end of the bar and sliding along slot in bar as shown in fig A.

2. Add the other three bolts in each of the none slotted holes in each of

the brackets. Lay the slotted part of each of the brackets over the bolts

on the bar. (fig B) Loosely tighten nuts so brackets can easily be

moved along bar.

3. Find a desired location for your light and if needed, drill three 5/16”

holes, position the brackets on the bar as needed and mount the light.

Up and down adjustments are made using the slots on the bracket.

Tighten all nuts securely.

KC HiLiTES, Inc., 2843 West Avenida de Luces, PO Box 155, Williams, AZ 86046 * 800-528-0950 * www.kchilites.com KC3265AQ - 022213

Instructions for

KC #325 (180w) or #326 (240w)

LED Light Bar System

FOR OFF ROAD USE ONL

Fig. B

Fig. A

Hole in Light

for Bolt Head

OFF

Résumé du contenu

Page 1 - LED Light Bar System

Bolts with Nutson BracketsThanks for choosing a KC HiLiTES product. We take pride in building the highest quality, best engineered systems possible. Y

Commentaires sur ces manuels

Pas de commentaire

Kc-hilites KC #326 (240w) LED Light Bar System Instructions Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Kc-hilites KC #326 (240w) LED Light Bar System Instructions. KC HiLiTES KC #326 (240w) LED Light Bar System Instructions User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Kc-hilites KC #326 (240w) LED Light Bar System Instructions