Kc-hilites KC #551 ATV Lighting Pair Packs Instructions Manuel d'utilisateur télécharger pdf

Thanks for choosing a KC HiLiTES product. We take pride in

7. Tighten the inside bolt until bracket is secure.

building the highest quality, best engineered systems

8. Repeat for second bracket.

possible. Your satisfaction with our product is important, so

if you have any questions, please call our customer service

Wiring Your Lights...

line at 800-528-0950. (M-F 7:30 - 5:00 MT)

1. Find a suitable flat surface that has an open space behind

(like the fairing), drill a 1/2” hole and mount the switch.

Parts included:

2. Remove the fuse from the red wire.

2 - 35 watt lights 1 - Wire set 1 - Switch

3. Plug the red and black wire set into the appropriate red and

7 ft - Protective tubing 8 - Wire ties 2 - Wire splices

black wires on the light furthest (#1) from the switch. (see

2 - Mounting brackets with hardware 1 - Alcohol pad

diagram)

4. Cut the terminals off of light #2. As you run the wire set past

light #2, attach light #2 red and black wires using the

CAUTION - These two lights draw approximately 6 amps total.

enclosed wire splices.

Contact your ATV dealer if you are not sure your electrical

system will handle the additional load.

Continue routing the red harness wire back to the switch and

plug it into one of the switch wires.

6. Attach the fused red wire to the other switch wire and route it

Mounting Your Lights...

back to the positive (+) battery terminal.

First determine the diameter of the bar on which you are

mounting these brackets. (1” or 3/4”)

Next determine where on the bar you want to mount

your lights.

Then follow the instructions below for your size bar.

1 Inch Bar

(do not use rubber shims)

1. Slip the curved bottom piece around the bar from the

underside. Hold in place while placing the flat piece on top

of the bar.

2. Align the inside holes and loosely bolt the brackets together.

3. Attach your light to the outside hole and tighten securely.

4. Tighten the inside bolt until bracket is secure.

5. Repeat for second bracket.

7. Route the black wire back to the battery and attach to the

3/4 Inch Bar

negative (-) post or other suitable ground.

1. Clean both parts of the bracket with enclosed alcohol pad or

8. Use the enclosed wire ties and protective tubing as needed to

similar solution.

secure and protect the wiring.

2. Find the 7/8” x 1 3/8” rubber shim. Peel off the protective

9. Replace the fuse in the red wire and test your lights.

backing and place it in the middle of the flat top bracket. (see

10. Adjust lights as needed.

figure 1) Press firmly in place.

11.YOUR DONE!

3. Find the 1 1/2” x 1 3/8” shim. Peel off the protective backing

and place it in the center of the “U” shaped area of the curved

bottom bracket. (see figure 1) Press firmly in place.

4. Slip the curved bottom piece around the bar from the

underside. Hold in place while placing the flat piece on top

of the bar.

5. Align the inside holes and loosely bolt the brackets together.

IF YOU HAVE ANY PROBLEMS OR QUESTIONS, PLEASE CALL

6. Attach your light to the outside hole and tighten securely.

CUSTOMER SERVICE AT 800-528-0950

Wiring and Mounting Instructions

For KC 420, 421, 422, 550 & 551

ATV Lighting Pair Packs

KC HiLiTES, Inc. 2843 W. Avenida de Luces, Williams, Arizona 86046-0155 * 800-528-0950 * www.kchilites.com KC3264T - rev 042304

23 Year Warranty

See details on our website at

www.kchilites.com

Place 7/8 x 1 3/8

shim here

Place 1 1/2 x 1 3/8 shim here

Fig. 1

Bracket with

Light Mounted

Wiring

Diagram

Black Wire

Red Wire

Battery

Switch

10A Fuse

Wire

Splice

Light

No. 1

Light

No. 2

How to Use

Wire Splice

1. Insert wires

2. Press metal tab down

3. Fold plastic tab over

Résumé du contenu

Page 1 - 23 Year Warranty

Thanks for choosing a KC HiLiTES product. We take pride in 7. Tighten the inside bolt until bracket is secure.building the highest quality, best

Commentaires sur ces manuels

Pas de commentaire

Kc-hilites KC #551 ATV Lighting Pair Packs Instructions Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Kc-hilites KC #551 ATV Lighting Pair Packs Instructions. KC HiLiTES KC #551 ATV Lighting Pair Packs Instructions User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Kc-hilites KC #551 ATV Lighting Pair Packs Instructions