Kc-hilites KC #6301 Wiring Kit for Two Lights Instructions Manuel d'utilisateur télécharger pdf

Installation Instructions

KC 6301 Wiring Kit for Two Lights

Thanks for choosing a KC HiLiTES product. We take pride in building

the highest quality, best engineered systems possible. Your

satisfaction with our product is important, so if you have any questions

or comments, please call our customer service line at 800-528-0950 or

visit our web site at www.kchilites.com.

1. PARTS INCLUDED IN YOUR WIRING KIT...

1 - Switch 1 - Panel

21 ft. of 14 ga wire 2 - Wire splice connectors

4 - Slide-on Terminals 3 - Sheet metal screws

5 - Nylon wire ties 1 - 20A fuse & carrier

1 - Fuse box tap clip 1 - Ring terminal

2.MOUNT ‘EM UP...

DRIVING LIGHTS - Where you mount your driving lights is extremely important,

as well as aiming the units. Too high and they will bounce right back at you and

you’ll be trying to look through the beam instead of down the road. Too low and

they’ll skim across the roadway and not illuminate correctly where you are trying

to see. Fortunately, the bumper on most vehicles works out perfectly. Mounting

right under or on top of it is ideal. Try and place the lights as far back toward the

grill as possible, this will keep the front of the lens behind the bumper and

minimize the chance of breakage from impact.

FOG LIGHTS - Since fog rarely settles right onto the roadway, fog lights will

perform most effectively when mounted low and aimed underneath the fog.

BUMPER MOUNTING - Choose a location on your bumper for mounting your

lights, ensuring they measure an equal distance from each end of the bumper.

After marking the location for mounting, drill the appropriate size hole for the

lights you are mounting. Install the lights and loosely tighten the nut (you will

secure them later after aiming).

3.GET YOUR LIGHTS WIRED...

a.Find a suitable location inside the passenger compartment for your switch,

mark and drill two 1/8” holes and loosely install the panel. Fit switch in panel

Diagram C

and tighten switch. (we will remove panel when attaching wires)

b.Ground both of the black wires coming out of the lights. In most cases you

can attach them to the mounting bolts. If the mounting surface is not metal

then you must extend the wires to a good chassis ground.

c.Starting from the light farthest from the panel, attach one end of the

supplied wire to the red wire coming out of the light using one of the wire

splice connectors (see diagram C). If there is a terminal on the light wire, cut

it off first. Continue routing the wire toward the panel to the second light and

attach that red wire using another wire splice connector.

d.Continue routing the wire inside the engine compartment, through the

firewall until you get to the switch and panel. Cut and strip the wire and

crimp on a slide-on terminal. Connect this wire to the middle tab on the

switch marked LOAD.

e.Find a metal surface to ground your switch. If the panel is mounted to a

metal surface you may use one of the panel mounting screws for the

ground. If not, find an existing screw nearby and cut a length of wire to go

between the switch and ground point. Attach a ring terminal to one end and

a slide-on terminal to the other. Connect one end of the wire to the switch

tab marked EARTH (this is tab on same side as green LED light on switch,

see wiring diagram below) and the other end to the grounded screw.

f.Attach a slide-on terminal to the remaining piece of wire and connect it to

the switch tab marked SUPPLY( remaining tab). Route the other end to a 12

volt power source. This may be your fuse block, battery or other junction

If you have any problems or questions, please

box. Before connecting to power source, install the in-line fuse carrier and

call customer service at 800-528-0950

fuse as shown in diagram C. If you use the fuse block, attach a slide-on

terminal and either slip it on an open accessory lug or use the enclosed ATO

fuse clip (see diagram C) and attach to existing fuse.

g.LIGHT ‘EM UP.

4.AIMING YOUR LIGHTS...

Proper aiming of your lights is important. This procedure is accomplished by

aiming your fog or driving lights in relation to your properly aimed headlights.

1. Place your vehicle approximately 25 feet and perpendicular to a flat surface

such as a garage door or building. It is important that the vehicle be on level

ground.

2. With low beam headlights on, go over to the surface on which they are

shining and mark the vertical center on both left and right headlights with

something easily removable like masking tape. You might use a short piece

of tape to show vertical center and a long piece for the horizontal portion.

Your tape should appear as below.

USE DIAGRAM “A” FOR AIMING FOG LIGHTS

USE DIAGRAM “B” FOR AIMING DRIVING LIGHTS

With these markings on the wall, aiming can be done very easily. Please

refer to the proper section below for the type of lights being aimed.

FOG LIGHTS - The vertical aiming of fog lights is very important. Because of

the low mounting position relative to the ground (12 to 30 inches), they

should be aimed parallel to the ground or lower. Fog lights should be aimed

so the cutoff is on or below your horizontal low beam wall marks for best

results. The side to side adjustments are up to you. A large center overlap

will increase center light and decrease overall width. A slight center overlap

will increase your side lighting and give even coverage overall.

DRIVING LIGHTS - Driving lights are used to supplement your high beams.

They should only be used in conjunction with high beam headlights. The

horizontal centers of the beams may be aimed at the same level as your high

beam tape marks on the wall. The width is up to you as you may prefer to

light the sides of the road at a distance rather than concentrating the majority

of the light down the middle.

OFF ROAD LIGHTS - Since lights such as these are not legal on any public

road or highway, aiming your off road or competition lights is entirely up to

you. Most prefer the beam to shine as far down the road as possible, others

adjust them slightly off to the sides.

KC HiLiTES, Inc. Post Office Box 155, Williams, Arizona 86046-0155 * 800-528-0950 * www.kchilites.com KC3265Y - 071309

Diagram B

The horizontal centers of the driving lamp beams may be aimed at

the same level as your high beam tapes on the wall.

Left High Beam

Right High Beam

Right Low Beam

Left Low Beam

KC Light KC Light

Fuse

Earth

Load

Supply

Wire

Splice

LED

Wiring Diagram

12 Volt

Power Source

Switch

Ground (earth)

Ground

(earth)

Diagram A

Fog lights should be aimed so that the top cutoff is on or below

your horizontal low beam wall marks.

Left Low Beam

Right Low Beam

See details on our website at

www.kchilites.com

23 Year Warranty

- - - CAUTION - - -

THIS WIRING KIT WILL NOT ACCOMMODATE

MORE THAN TWO 130 WATT LIGHTS

23 Year Warranty 1

Résumé du contenu

Page 1 - 23 Year Warranty

Installation InstructionsKC 6301 Wiring Kit for Two LightsThanks for choosing a KC HiLiTES product. We take pride in building the highest quality,

Commentaires sur ces manuels

Pas de commentaire

Kc-hilites KC #6301 Wiring Kit for Two Lights Instructions Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Kc-hilites KC #6301 Wiring Kit for Two Lights Instructions. KC HiLiTES KC #6301 Wiring Kit for Two Lights Instructions User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Kc-hilites KC #6301 Wiring Kit for Two Lights Instructions