Kc-hilites KC #6308 Wiring Harness Two 55W Lights Maximum Ins Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Kc-hilites KC #6308 Wiring Harness Two 55W Lights Maximum Ins. KC HiLiTES KC #6308 Wiring Harness Two 55W Lights Maximum Installation User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 1
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Thanks for choosing a KC HiLiTES product. We take pride in building the highest quality, best engineered systems possible. Your
satisfaction with our product is important, so if you have any questions, please call our customer service line at 800-528-0950. For
warranty information, visit our website at www.kchilites.com.
Parts Included
1 - Wiring Harness 3 - Sheet Metal Screws
1 - Switch & Panel 6 - Wire Ties
MOUNTING YOUR LIGHTS
1. Choose a location on your vehicle to mount your light(s). Mark the location for mounting and drill the appropriate size hole for
each light. Install the light(s) and loosely tighten. (you will secure them later when aiming)
WIRING YOUR LIGHTS
1. Remove the fuse from the harness. Find a suitable
location inside the passenger compartment for your
switch. Mark and drill two 1/8” holes, insert screws
and loosely install the panel to ensure fit. Remove
panel, install switch, and slide panel with switch
back in place. (Do not tighten. The panel and
switch will be removed when attaching wires.)
2. Connect the light wire(s) to the light(s) and route the
harness back toward the battery or other 12V power
source. Attach the YELLOW wire to the positive side
of the battery or power source. Attach the BLACK
wire to the negative side of the battery or chassis
ground.
3. Continue routing the YELLOW and RED wires of the
harness into the vehicle toward the switch. Once
the wires are inside the vehicle near the switch,
remove the panel with switch and attach the RED
wire to the switch terminal marked LOAD. Attach
the YELLOW wire to the switch terminal marked
SUPPLY. Attach one end of the BROWN wire to the
switch terminal marked EARTH and the other end to a good grounded metal surface under the dash. (use supplied screw and
washer if needed) Re-attach the panel with switch and tighten the screws.
4. Before replacing the fuse, ensure the switch is in the off position (see below). Replace the fuse and turn on your lights.
AIMING YOUR LIGHTS
Fog Lights - The vertical aiming of fog lights is very important. Because of the low mounting position relative to the ground (12
to 30 inches), they should be aimed parallel to the ground or lower. Fog lights should be aimed so the cutoff is on or below
your horizontal low beam for best results. The side to side adjustments are up to you. A large center overlap will increase
center light and decrease overall width. A slight center overlap will increase your side lighting and give even coverage overall.
Driving Lights - Driving lights are used to supplement your high beams. They should only be used in conjunction with high beam
headlights. The horizontal centers of the beams may be aimed at the same level as your high beam.
The width is up to you as you may prefer to light the sides of the road at a distance rather than
concentrating the majority of the light down the middle.
Off Road Lights - Since lights such as these are not legal on any public road or highway, aiming
your off road or competition lights is entirely up to you. Most prefer the beam as far down the
road as possible, others adjust them slightly off to the sides.
After aiming the lights to your preference, tighten all hardware.
YOU’RE DONE
KC HiLiTES, Inc., 2843 West Avenida de Luces, PO Box 155, Williams, AZ 86046 * 800-528-0950 * www.kchilites.com KC3265AC - 052113
Installation Instructions for
KC #6308 Wiring Harness
Two 55W Lights Maximum
OFF
ED
Wiring
Diagram
Switch shown
in Off Position
Vue de la page 0
1

Résumé du contenu

Page 1 - Two 55W Lights Maximum

Thanks for choosing a KC HiLiTES product. We take pride in building the highest quality, best engineered systems possible. Your sat

Commentaires sur ces manuels

Pas de commentaire